Just how to Troubleshoot as well as Repair an Electric Hot Water Heater
Just how to Troubleshoot as well as Repair an Electric Hot Water Heater
Blog Article
We have encountered the article on No Hot Water — Water Heater Repair down the page on the internet and think it made sense to write about it with you over here.
Numerous modern-day houses take advantage of an electric hot water heater for their heating unit, as a result of its benefit and also simplicity of use. Nonetheless, much like any other electric appliances, issues may arise with its use, unexpectedly. It can be truly frustrating to awaken to a cold shower rather than a warm one or having your bath with water that isn't warm enough and even also hot. Whatever the situation might be, water heater troubles can be quite stressful. The good news is, we've made a listing of feasible services to your hot water heater issues. There are a number of variables that could trigger most of these problems, it could be a concern with the power supply, the electrical heating element, or the thermostat. Prior to doing anything, guarantee you turn off the primary power supply for safety and security. Whatever the problem is, getting it repaired ought to not posture way too much of a concern if you comply with these steps:
Call A Specialist:
If after changing all defective components and also resetting your temperature, the water heater still isn't working, you might require to contact an expert plumber for an expert point of view. The trouble with your heater could be that the hot and cold taps have actually been switched over or it might be undersized for the amount of hot water needed in your home. Whatever the situation might be, a specialist plumber would certainly help address the problem.
Check Your Power Supply:
As basic as this may seem, it is extremely needed. Without ample power, your hot water heater will not function. So the first thing to do when your water suddenly stops working is to verify that it isn't a power issue. Inspect if the fuse is burnt out or the breaker stumbled. If the breaker is the problem, just transform it on and off once more. Change any kind of busted or damaged fuse. Check the device with power after these modifications to see if it's currently functioning.
Inspect Your Thermostat:
If your hot water heater still isn't working or the water coming out isn't hot enough, you may need to check the temperature setups on your top thermostat. Make certain the breaker is turned off before doing anything. Open the access panel and press the red button for temperature level reset over the thermostat. This need to aid heat up the water. Turn the circuit breaker back on and also examine if the trouble has actually been fixed.
Inspect the Burner in the Hot Water Heater:
If it's not a power issue, then try checking out your heating element if it is still functioning. Check each of your burner to make sure the problem isn't with any one of them. If any one of them is defective, replace that part and afterwards inspect whether the hot water is back on.
Conclusion
Hot water heater troubles are not constantly major. Many of them result from small problems like a blown fuse or worn-out heating element. Changing the malfunctioning parts should suffice. Nonetheless, if you are still not able to solve the trouble, give a call to your nearby plumber to find to get it fixed.
What Would Cause My Electric Water Heater to Stop Working?
Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.
To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.
Basic Water Heater Troubleshooting
Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.
If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.
If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.
When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.
Conduct Advanced DIY Water Heater Troubleshooting
If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.
Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:
The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.
If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.
The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.
While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.
Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.
While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.
https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working
We are very intrigued by How to Troubleshoot and Repair an Electric Water Heater and I am assuming you liked my post. If you enjoyed reading our blog posting kindly make sure you remember to share it. Many thanks for your time spent reading it.
Request Free Estimate
Report this page